联系我们

联系我们

地址:济南市高新区舜华路2000号舜泰广场9号楼5层502-2

电话:15066665432

传真:0531-88984022

联系人:殷经理

邮箱:jnyygt@126.com

网址:www.jnyygt.com

新闻资讯

当前位置: 首页 - 新闻资讯

钢板在后期加工时,会因为翘曲导致切割后变形,造成工件报废,影响用户正常使用,同时造成企业经济损失。分析认为钢板经热轧后内部及上下表面存在残余应力,如果残余应力沿钢板宽度和长度方向呈不均匀分布,将会对钢板截面产生一个力矩,使钢板在分切后发生翘曲。控制措施是:

When the steel plate is processed in the later period, the deformation will be caused by the warping, which causes the work piece to be scrapped, which affects the normal use of the user and causes the economic loss of the enterprise. It is considered that there is residual stress in the inner and upper surface of the steel plate after hot rolling. If the residual stress is uneven distributed along the width and length of the steel plate, it will produce a torque on the section of the steel plate, causing the steel plate to warp after cutting. The control measures are:

1、由于采用超快速冷却,提高了形核率,细化了铁素体晶粒。保持超快冷状态到相变点附近停止冷却,随后进行冷却路径控制,得到优良性能的钢板。

 济钢一级代理商

1. Due to the use of ultra fast cooling, the nucleation rate was improved and ferrite grain was refined. The super fast cold state is kept near the phase transition point to stop cooling, and then the cooling path is controlled to get the excellent performance steel plate.

2、冷却温度

2. Cooling temperature

层流冷却造成的内应力不均衡问题主要是由3种不均匀冷却导致: 横向冷却严重不均匀;厚度方向冷却不对称;横向和厚度方向冷却不均匀混合。

The problem of internal stress imbalance caused by laminar cooling is mainly caused by 3 kinds of non-uniform cooling: severe non-uniform cross cooling, asymmetric thickness direction, uneven cooling in transverse direction and thickness direction.

3、冷矫直

3. Cold straightening

矫直能改善钢板残余应力分布,当钢板在横断面上有应力分布不均时,可以需要采取弯辊措施以增加局部变形的方法来补偿纵向纤维的长短不齐,达到消除波浪弯、均匀化钢板内应力的目的。

The straightening plate can improve the residual stress distribution, when the steel plate is uneven stress distribution in cross section, may need to take measures to increase the bending method of local deformation to compensate for the uneven length of longitudinal fibers, to eliminate the wave bending and uniform stress to steel plate.

本文由 济钢一级代理商友情奉献,更多有关的知识请点击:http://www.jnyygt.com我们将用最先进的技术,最真诚的态度,为您提供最为全面的服务。我们将会陆续向大家奉献,敬请期待。

This article is from the first tier agents of Jigang, and more knowledge is available. Please click: http://www.jnyygt.com, we will provide you with the most advanced technology and the most sincere attitude to provide you with the most comprehensive service. We will continue to contribute to you and look forward to it.


上一篇:镀铝锌彩涂板的设计和选用要点
下一篇:最后一页

 
在线咨询 在线咨询
全国咨询热线
15066665432